PXD-3710/PXD-3710F 3U Pentium-III System Controller and PXD-R3000 RTM User’s Manual Recycled Paper
6 • Introduction 1.1 Unpacking Checklist Check the shipping carton for any visible damage. If the shipping carton and contents are damaged, notify the
Introduction • 7 1.2 Features 1.2.1 PXD-3710/3710F Features Standard 3U PXI form factor PICMG 2.0 CompactPCI specification R3.0 compliant PICMG 2.1
8 • Introduction 1.3 Functional Block Diagram The following topics overview the PXD-3710 main features as shown in the functional block diagram belo
Introduction • 9 I/O extensions, including the serial port COM2, USB port #3, graphic interface extension to DVI, and ATX power supply interface.
10 • Introduction 1.3.5 Graphic Interfaces The Intel 815E GMCH2 chip is integrated with an AGP 2X, ACPI, and VESA compliant hyper-pipelined architect
Introduction • 11 storage device. Only one device can be connected with the IDE interface. In addition to the 40-pin IDE connector, a 4-pin power conn
12 • Introduction 1.3.11 IEEE-1284 Parallel Port/Printer Interface The parallel I/O interface signals are routed to the DB-25 connector on the front
Introduction • 13 1.4 Specifications General CompactPCI Features PICMG 2.0 CompactPCI specifications R3.0 compliant PICMG 2.1 R1.0 CompactPCI Hot
14 • Introduction IEEE 802.3 10Base-T/100Base-TX compatible Supports Intel pre-boot execution environment (PXE) for remote booting in Windows NT/200
Introduction • 15 Shock: 15G peak-to-peak, 11ms duration, non-operation Vibration: Non-operation: 1.88GRMS, 5-500Hz Operation: 0.5GRMS, 5-50
©Copyright 2003 ADLINK Technology Inc. All Rights Reserved. Manual Rev. 1.00: March 10, 2004 Part No. 50-17006-100 The information in this document
16 • Introduction 1.5 Peripheral Connectivity Connectors PXD-3710 Front Faceplate PXD-3710 On-board PXD-R3000 On-board PXD-R3000 Rear Faceplate VGA D
Jumpers and Connectors • 17 2 Jumpers and Connectors This chapter provides information about the board outline, connector definitions, and jumper sett
18 • Jumpers and Connectors 2.1 PXD-3710/3710F Board Outline and Illustratoin 2.1.1 PXD-3710/3710F Front View Figure 2: PXD-3710/3710F Front
Jumpers and Connectors • 19 2.1.3 DB-3710L2 Daughter Board Figure 4: DB-3710L2 Daughter Board 2.1.4 DB-3710L3 Daughter Board Figure 5: DB-3710L
20 • Jumpers and Connectors 2.2 PXD-3710/3710F Connector Pin Assignments 2.2.1 VGA Connector Signal Name Pin Pin Signal Name Red 1 2 Green Blue 3
Jumpers and Connectors • 21 2.2.4 Parallel Port Connector Signal Name Pin # Pin # Signal Name Line printer strobe 1 14 AutoFeed PD0, parallel d
22 • Jumpers and Connectors 2.2.6 COM1 Serial Ports (RS-232/422/485) The PXD-3710/3710F COM1 serial port can be configured as RS232, RS422 or RS485
Jumpers and Connectors • 23 2.2.9 CompactPCI Connectors P1/J1 Pin A B C D E F J1-25 +5V REQ64#(1)ENUM#(2) +3.3V +5V GNDJ1-24 AD[1] +5V NC AD
24 • Jumpers and Connectors 2.2.10 CompactPCI Connectors P2/J2 Pin A B C D E F J2-22 NC NC NC NC NC GND J2-21 CLK6 GND NC NC NC GND J2-
Jumpers and Connectors • 25 2.3 PXD-3710/3710F Jumpers Setting The PXD-3710/3710F is designed for maximum flexibility with as few jumpers as possible
Getting Service from ADLINK Customer Satisfaction is top priority for ADLINK TECHNOLOGY INC. If you need any help or service, please contact us. ADLI
26 • Jumpers and Connectors 2.3.2 CF1 Master Slave Selection CF1 master/slave DB-3710L2 CN7 CF1 Master 2-3 (Default) CF1 Slave 1-2 Table 16:
Jumpers and Connectors • 27 2.4 PXD-R3000 Board Outline and Illustratoin 2.4.1 PXD-R3000 Component side View Figure 6: PXD-R3000 Compon
28 • Jumpers and Connectors 2.5 PXD-R3000 Connector Pin Assignments 2.5.1 FPD Connector CN1 Pin Signal Pin Signal Pin Signal Pin Signal 1 NC 2
Jumpers and Connectors • 29 2.5.3 DVI Connector CN4 Pin Signal Pin Signal Pin Signal 1 TX2- 9 TX1- 17 TX0- 2 TX2+ 10 TX1+ 18 TX0+ 3 GND 11 G
Getting Started • 31 3 Getting Started This chapter gives a summary of what is required to setup an operating system using the PXD-3710/3710F. Hardwar
32 • Getting Started PXD-3710/3710F main board and DB-3710L2 daughter board, so we recommend that users have RAM installed professionally by ADLINK. F
Getting Started • 33 3.3 BIOS Configuration Overview On the PXD-3710/3710F BIOS, ADLINK provides the following key features: PCI Plug and Play sup
34 • Getting Started 3.4 Operating System Installation For more detailed information about the operating system, refer to the documentation provided
Driver Installation • 35 4 Driver Installation 4.1 Hardware Configuration File Installation This section describes system requirements of the Intel 8
36 • Driver Installation Insert the ADLINK All-In-One CD, run SETUP.EXE at X:\PXI_Platform\PXI Controller\PXI-3710_3710F\Chipset\I815\Win9x2k\Disk1
Driver Installation • 37 4.2 VGA Drivers Installation This section describes the VGA driver installation for the on-board VGA controller Intel 815E
38 • Driver Installation Novell Netware, DOS Setup for Novell NetWare DOS All the above drivers are included in the ADLINK All-In-One CD. In the f
Driver Installation • 39 4.3.3 LAN Driver Installation on Windows 98 Windows 98 will attempt to install a LAN driver automatically. To guarantee comp
40 • Driver Installation 4.3.4 LAN Driver Installation on Windows NT Windows NT may ask to install a LAN driver from its own library of drivers. We
Watchdog Timer & Utilities • 41 5 Utilities This chapter explains extended functions of the PXD-3710/3710F controller, including watchdog timer, I
42 • Watchdog Timer & Utilities The PXD-3710’s custom watchdog timer circuit is implemented in a programmable logic device. The watchdog timer con
Watchdog Timer & Utilities • 43 (2) Reboot the system. You can also write your own DLL by referring to the DOS sourced ADLINK has provided. 5.2
44 • Watchdog Timer & Utilities 5.3 PICMG 2.1 Hot Swap Support The PXD-3710/3710F Hot-Swap capability allows non-system slot boards to be added o
Warranty Policy • 45 Warranty Policy Thank you for choosing ADLINK. To understand your rights and enjoy all the after-sales services we offer, please
Table of Contents • i Table of Contents List of Tables...iii List of
46 • Warranty Policy RMA Request & Confirmation Form Dear Customer, Page 1 of 2 Please fill out and fax back this form to obtain the RMA num
Warranty Policy • 47 Page 2 of 2 Note: 1. Please give specific details of the def
ii • Table of Contents 2.2.9 CompactPCI Connectors P1/J1 ...23 2.2.10 CompactPCI Connectors P2/J2...
List of Tables and Figures • iii List of Tables Table 1: Peripheral Connectivity Table... 16 Table 2: V
iv • How to Use This Guide How to Use This Manual This manual is intended to assist users to configure the PXD-3710/3710F 3U system controller. It is
Introduction • 5 1 Introduction The PXD-3710 series is an OEM version 3U system controller from ADLINK that supports an LCD interface and extra USB po
Comments to this Manuals