ADLINK Technology PXIS-2680P User Manual

Advance Technologies; Automate the World.Manual Rev. 2.00Revision Date: January 28, 2005Part No: 50-17019-100PXIS-2680P8-Slot 3U PXI Portable Inst

2IntroductionThe PXIS-2680P includes a 15” SVGA LCD touch screen—anadditional monitor is not necessary. No additional LCD, touchpanel, or keyboard wir

Introduction 31.2 SpecificationsComplies with PXI Rev.2.2 specifications and accepts modulescompliant with CompactPCI, PICMG 2.0 specificationsElectr

4IntroductionCoolingX Two 8cm, 12VDC ball bearing fans, 41CFM air flow/eachPhysicalX Number of PXI/CompactPCI slots: 8 (1 controller, 7 periph-erals)X

Introduction 5ReliabilityX MTBF:Z Backplane: 800,000hrsZ Power Supply: 100,000hrs @ full load1.3 Mechanical Drawing and OutlineMechanical DrawingFigu

6IntroductionOutlineFigure 1-3: PXIS-2680P Front Panel ViewFigure 1-4: PXIS-2680P Rear View

Introduction 7Figure 1-5: PXIS-2680P Left Hand Side ViewFigure 1-6: PXIS-2680P Right Hand Side View

8Introduction

Getting Started 92 Getting StartedIn this chapter, the unpacking procedure of the sub-system andhow to configure a portable PXI system is described.

10 Getting StartedFigure 2-1: System Controller Installation2. Push the handle until it clips in place. You will hear aclick sound when the handle has

Getting Started 113. Insert the controller board mounting screws and screwtightly.Figure 2-3: Mount the Controller Card with Screws4. When taking out

Copyright 2005 ADLINK TECHNOLOGY INC.All Rights Reserved. The information in this document is subject to change without priornotice in order to improv

12 Getting StartedPeripheral Module Installation1. Smoothly slide the peripheral module into an availableperipheral slot. Make sure that the periphera

Getting Started 13Removing and Installing a Power Supply1. Unscrew and remove the side panel.Figure 2-6: Removing the Power Supply (A)

14 Getting Started2. Pull out the power supply while pressing.Figure 2-7: Removing the Power Supply (B)3. To replace, push and slide in the new.Figure

Getting Started 152.3 Operation InstructionsHow to Release Keyboard and Touch PadThere are two release buttons located at the top-left and top-righto

16 Getting StartedHow to Setup the KeyboardThe keyboard cable is located on the top portion of the keyboard;it is a coil cable with an RJ-45 connector

Getting Started 17Keyboard PositioningThe keyboard angle can be adjusted by tilting the keyboard feetlocated at the bottom.Figure 2-11: Positioning t

18 Getting StartedLCD DisplayThe LCD display has a fixed mechanism. You can pull up the pairof feet at the bottom of the case to lift the LCD display

Getting Started 19Figure 2-14: PXIS-2680P DVD-ROMCooling FansThe cooling fans are located at the rear of the chassis for easyaccess. There are two co

20 Getting Started2.4 Software InstallationTo enable the touch panel functionality, users need to first installthe driver into the system controller.

Getting Started 21The LCD On/Off button turns the LCD on or off with each press.Figure 2-16: System Monitoring Panel Power LEDTemp. LEDAlarm reset bu

Getting Service from ADLINKCustomer Satisfaction is top priority for ADLINK Technology Inc.Please contact us should you require any service or assista

22 Getting Started

Backplane Overview 233 Backplane OverviewThe cBX-3008L backplane can accept both PXI compatible prod-ucts and standard CompactPCI products. The signa

24 Backplane OverviewFigure 3-1: PXI Local Bus and Star Trigger RoutingLocal BusThe PXI backplane local bus of the cBX-3008L is a daisy-chainedbus tha

Backplane Overview 25asynchronous external events the system is monitoring or control-ling.System Reference ClockThe PXIS-2680P supplies the PXI 10MH

26 Backplane Overview3.2 Mechanical DrawingThe following figures show the two parts of the backplanes andmechanical drawing.Figure 3-2: cBX-3008L Fron

Backplane Overview 273.3 Pin AssignmentSystem ControllerPin Z A B C D E F25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O) AD[0] ACK64# GN

28 Backplane OverviewPin Z A B C D E F22 GNDPXI_BRSVA22 PXI_BRSVB22 PXI_BRSVC22 PXI_BRSVD22 PXI_BRSVE22GND21 GNDCLK6GNDNCNCNCGND20 GNDCLK5 GND NC GND

Backplane Overview 29Star TriggerPin Z A B C D E F25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O) AD[0] ACK64# GND23 GND +3.3V AD[4] AD[

30 Backplane OverviewPin Z A B C D E F22 GNDPXI_BRSVA22 PXI_BRSVB22 PXI_BRSVC22 PXI_BRSVD22 PXI_BRSVE22GND21 GNDPXI_LBR0 GND PXI_LBR1 PXI_LBR2 PXI_LBR

Backplane Overview 31General PeripheralPin Z A B C D E F25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O) AD[0] ACK64# GND23 GND +3.3V AD[

32 Backplane OverviewPin Z A B C D E F22 GNDPXI_BRSVA22 PXI_BRSVB22 PXI_BRSVC22 PXI_BRSVD22 PXI_BRSVE22GND21 GNDPXI_LBR0 GND PXI_LBR1 PXI_LBR2 PXI_LBR

Backplane Overview 33Note: Please refer the following table for the routing of the Bus Mastering (REQ/GNT), IDSEL, PCI CLK, and Interrupt sig-nals.N

34 Backplane Overview

Troubleshooting and Maintenance 354 Troubleshooting and Maintenance4.1 TroubleshootingInstallation Issues: 1. Failure to power on is typically due to

36 Troubleshooting and MaintenanceNo Display (LCD):1. Check that all the proper power up procedures has beentaken.2. Hook up an external CRT to the VG

Troubleshooting and Maintenance 374.2 MaintenancePXIS-2680PYou should always make sure that the keyboard assembly is prop-erly attached onto the PXIS

38 Troubleshooting and MaintenanceCleaning the LCD1. Do not use cleaners that contain alcohol.2. Do not use a cloth that could be abrasive to the surf

Important Safety Instructions 39Important Safety InstructionsPlease read and follow all instructions marked on the product andin the documentation be

40 Important Safety InstructionsX Openings in the case are provided for ventilation. Do notblock or cover these openings. Make sure there is adequates

Warranty Policy 41Warranty PolicyThank you for choosing ADLINK. To understand your rights andenjoy all the after-sales services we offer, please read

Table of Contents iTable of ContentsTable of Contents... iList of Tables...

42 Warranty Policy3. Our repair service is not covered by ADLINK's two-yearguarantee in the following situations:X Damage caused by not following

ii Table of ContentsTrigger Bus ... 24System Reference Clock ...

List of Tables iiiList of TablesTable 1-1: Electrical Output ... 3Table 3-1: JP2 and JP3 PXI

iv List of FiguresList of FiguresFigure 1-1: PXIS-2680P 3U PXI Portable Instrument Chassis ... 1Figure 1-2: PXIS-2680P Mechanical Drawing...

Introduction 11 IntroductionADLINK PXIS-2680P is a highly integrated and fully mobile 3UPXI instrument chassis offering 8-slot capacity for modules.D